HORIZONTAL SPLIT CASE PUMP
A horizontal split case pump is a unique type of Centrifugal Pump whose casing is divided into two distinct chambers, which is different from end suction pumps that are assembled with the suction nozzle, discharge nozzle and casing in one chamber. FIREGUARD offers FGSF series state-of-the-art Split Case Pumps with Diesel Engine or Electric Motor driven pumps FIREGUARD PUMPS are engineered with fully enclosed double suction impellers. Minimal axial thrust due to double entry impeller. In-line axially split design which permits removed of the complete rotor without removing the pipe and driver. Split Case Pumps are better when the water source is located above ground providing a positive suction FIREGUARD PUMPS are typically used in fire fighting applications for supplying water to the fire hose reels, fire hydrants or sprinkler systems. FIREGUARD PUMPS have a FLOW ranges from 300 to 8000 US GPM and Pressure ratings from 80 PSI up to 300 PSI
Horn And Strobe
The IQ673HS Strobes is addressable multi-candela visual and audible signal appliances with light sources generated from a white LED, listed according to UL 1971, UL 1638 and UL 464 for indoor use. The LED light source offers superior performance, including low power consumption and long operating life. Each appliance has the intelligence to report its location (the device address) and status to the Fireguard series fire alarm control panels. Six levels of light output are selectable. Relative light outputs in horizontal and vertical dispersion from strobes mounted on walls/ceilings. The strobe appliances produce a flash rate of one flash per second over the Regulated Voltage Range. The temporal tone generated by the horn portion is designed as per ANSI and NFPA72 for standard emergency evacuation signaling requirements. The appliance has the feature that can synchronize multiple horns and/or strobes in a complete fire alarm system. The IQ673HR Horns are addressable audible signal appliances listed according to UL 464 for indoor use. The temporal tone generat ed by the horn portion is designed as per ANSI and NFPA72 for standard emergency evacuation signaling requirements. The horn has a feature that can synchronize multiple horns in a complete fire alarm system.
INLINE BALANCE PRESSURE FOAM PROPORTIONER
The Inline Balance Pressure Foam Proportioners are used with positive displacement foam concentrate supply pump. The system controls accurately the flow of foam concentrate into the water stream over a wide range of flow rate and pressure. The Inline Balance Pressure Foam Proportioning System is used for simultaneous operation of the multiple foam injection even with different pressures between the two-injection point with a single concentrate supply line. Various sizes of inline balance pressure proportioners can be combined to suit the flow requirement of each hazard area.
Input Module IQ611M
The IQ611M input module monitors a single contact. The input line is monitored for open line faults and ground faults, and the contact must thus be wired with an end-of-line resistor. It is an intelligent addressable module and takes one address on the Signaling Line Circuit (SLC) or Data Communication Link (DCL) of the fire alarm control panel. The IQ611M is a UL listed device according to UL864 for Fire Protective Signaling Systems, for indoor use. The type of input contact is configurable.
Input-Output Module IQ611MO
The IQ611MO input-output module provides one 24VDC output and one feedback input monitor. The input line is monitored for open line faults and ground faults, and the contact must thus be wired with an end-of-line resistor. The output line is monitored for open lines, short-circuit faults, ground faults, and external 24VDC power source loss. It is a UL listed device according to UL864 for Fire Protective Signalling Systems for indoor use and FM. When the output is activated the device red LED will indicate the event condition by blinking longer. When the feedback is activated the device red LED will indicate the event condition by blinking twice. A return to the normal condition will cause the event to disappear and the device LED indicator will return to blinking every 4 seconds. The IQ611MO is an intelligent addressable module and takes one address on the Signalling Line Circuit (SLC) or Data Communication Link (DCL) of the fire alarm control panel.
INPUT/OUTPUT ADDRESSABLE MODULE WITH SHORT CIRCUIT ISOLATOR
The new series of analogue multi modules of the FG901MI line implements supervision and monitoring functions for the activation and supervision of auxiliary devices. Each FG901MI can be addressed manually, by programmer or by fire detection control unit with protocol or with auto addressing by fire detection control unit with protocol. The input channels monitor the rest, alarm and fault condition through the balancing resistors provided. The output channels can be either monitored or form C type. In the case of monitored output, the end of line (cut, short cables) and the presence of the power supply on the load, supplied with end-of-line resistance and diode are checked. In the case of form C output, the module offers potential-free relay contacts.
IQ805 SERIES EXTINGUISHING CONTROL PANEL
Q805 is an Intelligent Fire Alarm Control Panel (FACP) designed for small and medium-scale facilities. The FACP is ideally suited for both new and retrofit commercial, institutional, and industrial fire detection and notification applications. It is with dual hazard agent releasing that meets the requirement of UL864, and CAN/ULC-S527. The FACP support up to 252 devices, 2 NACs and three Form-C relays (pre-programmed for Alarm, Trouble an Supervisory). In addition, the control panel can be used for hazard agent releasing application via the SLC loop.
Features
- 1 signal Line Circuits and 252 addressable devices/points
- Up to 2 Notification Appliance Circuits
- 3 form C dry relay contacts
- 16 built in annunciator zones
- Up to 2 releasing zone
- A 2.8” true color LCD
- Up to 16 zone LED annunciator
K12 WET CHEMICAL FIRE SUPPRESSION SYSTEM
Even the most meticulously maintained and efficiently operated commercial and industrial kitchens can still experience unexpected mishaps. This is because fire is used as a medium of cooking, along with a whole host of cooking appliances and flammable materials present, the risk of fire in kitchens is always high. Fireguard K12 Commercial Kitchen Suppression Systems are a cutting-edge, automated, engineered solution that are designed to address the unique fire risks that a commercial kitchen environment poses. These systems are certified to the UL 300 standard and adhere to the NFPA 96/17A guidelines.
LANDING VALVES
Fireguard produces various types of landing valves such as oblique landing valve, right angle landing valve, flanged right angle landing valve, Bib nose type, Horizontal type and flanged straight through landing valve. All landing valve are manufacture to BS 5041 Part 1 & Part2. These valves are supplied with a 21/2" Instantaneous female outlet but are available with most other international adaptors as well with either flanged or threaded inlets. Models:
- Model: FG06-198A-00
- Model: FG06-198A1-00
- Model: FG06-198B-00
- Model: FG06-198B1-00
- Model: FG06-198B2-00
- Model: FG06-200A-00
- Model: FG06-200A1-00
- Model: FG06-200B-00
- Model: FG06-200B1-00
- Model: FG06-200C-00
- Model: FG06-200C1-00
- Model: FG06-200D-00
- Model: FG06-200D1-00
MANUAL CALL POINT
A modern stylish Fireguard FG921 Manual Call Point designed to provide greater aesthetic appeal. A low profile surface mounting MCP blends in with today's modern architectural styles. The FG921 MCP is ideal where emergency situations are identified and require an immediate evacuation. The FG921 range offers improved features for both the end user and the installer. A single maintenance tool provides access to test, reset and release the lid to change the glass or reset the element. The FG921 is fully compatible with all conventional systems available on the market. The new MCP is EN54 compliant LPCB Approved
Features
- Conventional resettable MCP
- Clearly visible alarm signal indication
- Anti-tamper facility
- Easy installation and maintenance
- FG921
- FG921-F
- FG921-TC
- FG921-FTC
MANUAL PULL STATION
The FGMS manual pull station is a high quality non toxic die-cast manual pull station. Low profile design and smooth edges offer an attractive yet functional design. All components are Powdered coated or have plated surfaces and inhibit corrosion. Electrically the FGMS manual pull station is unbeatable with 10 amp snap action switch offered in all possible contact arrangements (including gold contacts). The FGMS pull station can be used with or without a break glass rod with replacement requiring no special tools. All stations are Red, unless otherwise indicated.
Features
- Other features include
- Lift and pull
- Break glass cover
- Institutional key lock
- Weather and explosion proof versions
- All stations offer hex screw or key lock access
- Brass plated and other color options available
